Revision 1 posted to Storage - Wiki by LScheuplein on 7/26/2016 8:02:48 PM
Dell XC430 Web-Scale Hyperconverged Appliance Support Matrix
What's New!
This is the first edition of the online version of the Support Matrix. Check here for the newest updates to this document.
This document provides information about the supported software, firmware, and hardware versions and technical specifications for the Dell XC430 Web-Scale Hyperconverged Appliance.
This Support Matrix contains the latest compatibility and interoperability information. If you observe inconsistencies between this information and other documentation or references, this document supersedes all other documentation.
Supported hardware, firmware and software (Back to top)
This chapter provides information about supported software, firmware, and hardware versions for the Dell XC430 Web-Scale Hyperconverged Appliance.
Supported components
This section provides information about components supported by your hardware.
Supported Components| Component | v3 Version | v4 Version |
|---|
| CPUs | E5-2620 v3 | E5-2620 v4 |
| | E5-2630 v3 | E5-2630 v4 |
| | E5-2650 v3 | E5-2643 v4 |
| | E5-2660 v3 | E5-2650 v4 |
| | E5-2680 v3 | E5-2660 v4 |
| | E5-2595 v3 | E5-2680 v4 |
| | | E5-2690 v4 |
| | | E5-2595 v4 |
| | | E5-2598 v4 |
| BIOS | 1.2.6 and later | 2.0.0 or later |
| iDRAC support | 2.15.10.10 or later | 2.30.30.30 or later |
Supported physical disk drives (Back to top)
This section provides information about disks drives supported by your hardware.
Supported Physical Disk Drives| Form Factor | Capacity | Type | Vendor |
|---|
| 3.5" | 4 TB | NL-SAS HDD | Dell Supported |
| 3.5" | 6 TB | NL-SAS HDD | Dell Supported |
| 2.5" | 200 GB | SATA SSD | Intel® Solid-State Drive Data Center S3700 Series: 200 GB, 400 GB and 800 GB |
| 2.5" | 400 GB | SATA SSD | Intel® Solid-State Drive Data Center S3710 Series: 200 GB, 400 GB and 800 GB |
| 2.5" | 800 GB | SATA SSD | Intel® Solid-State Drive Data Center S3610 Series: 800 GB and 1.6 TB |
| 2.5" | 200 GB | SAS SSD | HGST |
| 2.5" | 400 GB | SAS SSD | HGST |
| 2.5" | 800 GB | SAS SSD | HGST |
This section provides information about Host Bus Adapters (HBA) supported by your hardware.
Supported HBAs| Name | Form factor/Slot | Minimum firmware version |
|---|
| H730 | Mini or integrated slot | 25.3.0-0016 |
| HBA330 | Mini or integrated slot | 9.17.20.07 |
This section provides information about networking supported by your hardware and supported NICs.
Intel branded Network Daughter Cards (NDC) and Network Interface Cards (NIC) specify the use of only Intel branded SFP+ optical modules for use with optical cables. When ordering a system with optics, the appropriate Intel branded SFP+ optical modules are included with your order. If you already have SFP+ optical modules, ensure they are the Intel branded modules before inserting into the NDC or NIC. Twinax cables are also the supported network cables for Intel NDC and NIC.
CAUTION: Using any brand of SFP+ module other than Intel during deployment disables the 10 GbE ports. Call Dell Support to recover port functionality.
WARNING: Hot-plugging an unsupported SFP+ module causes ESXi host to fail with purple diagnostic screen. Call Dell Support to recover from this situation.
Supported Networking| Name | Minimum firmware version |
|---|
| Broadcom Dual 1GbE LOM | 7.10.59 |
Supported NICs| Name | From factor or Slot | Minimum firmware version | Supported cables |
|---|
| Intel X520 Dual 10 G SFP+ | Low profile/any slot | 16.0.24 | Intel branded SFP+ modules only (10 GbE) Twinax Cable (10 GbE) |
| Intel X540 Dual 10 G BaseT | Low profile/any slot | 16.0.24 | Standard Category 6 Ethernet (up to 10 GbE) |
Supported hardware management solutions (Back to top)
This section provides information about hardware management solutions that are supported by your hardware.
Supported hardware management solutions| Name | Minimum firmware version |
|---|
| Dell OpenManage Essentials | 2.0 |
| Dell Nautilus Firmware Update Utility | A13 |
Supported management software (Back to top)
This section provides information about components supported by your hardware.
Supported management software| Name | Minimum version |
|---|
| Nutanix Operating System (NOS) | 4.1.3 |
This section provides information about the hypervisor Operating Systems (OS) supported by your hardware.
Supported hypervisor OS| Name | Minimum firmware version |
|---|
| VMware | ESXi 5.5, update 2 ESXi 6.0 |
| Windows Server | Windows Server 2012 R2 Standard Edition Windows Server 2012 R2 Datacenter Edition |
| Acropolis Hypervisor (AHV) | Nutanix 20150616 |
This chapter provides technical specifications for Dell XC430 Web-Scale Hyperconverged Appliance.
Physical specifications
This section provides expansion physical specifications for storage, including height, width, depth, maximum configuration weight and empty weight.
Physical specifications| Physical | Specification |
|---|
| Height | 42.8 mm (1.68 inch) |
| Width with rack latches | 482.4 mm (18.99 inch) |
| Width without rack latches | 434.0 mm (17.08 inch) |
| Depth (excludes bezel) | 607.0 mm (23.9 inch) |
| Weight (Maximum) | 19.9 kg (43.87 lb) |
| Weight (Empty) | 16.73 kg (36.88 lb) |
This section provides processor specifications required for your hardware.
Processor specifications| Type | Specification |
|---|
| Intel Xeon processor | EP E5-2600 v3 and v4 product family |
This section provides expansion bus specifications for storage, including bus type, expansion cards, and expansion slots.
Expansion bus specifications| Expansion Bus | Specification |
|---|
| Bus type | PCI Express Generation 2 and 3 |
| Expansion slots using riser card |
PCIE_G3_X16
| (Slot 1) one low profile, half-length x16 link for processor 1
(Slot 2) one low profile, half-length x16 link for processor 1 |
PCIE_G3_X8
| (Slot 1) one full-height, half-length x8 link for processor 1
(Slot 2) one half-height, half-length x8 link for processor 1 |
This section provides power specifications for your hardware, including wattage, heat dissipation, and
voltage.
NOTE: This system is also designed to connect to IT power systems with a phase to phase voltage not exceeding 230 V.
Power Specifications| Type | Specification |
|---|
| AC power suply unit (PSU) |
| Wattage | 550 W |
Heat dissipation NOTE: Heat dissipation is calculated on the basis of power rating of PSU. | 550 W (Platinum) AC (100–240 V, 50/60 Hz, 7.4 A–3.7 A)
2107 BTU/hr (550W PSU)
|
| Voltage | 100–240 V AC, auto ranging, 50/60 Hz |
This section provides memory specifications for your hardware, including architecture, memory module sockets, and memory module capacities.
Memory Specifications| Memory | Specification |
|---|
| Architecture | 2133 MT/s, 2400 MT/s DDR4 DIMMs Support for advanced ECC or memory-optimized
operation |
| Memory module sockets | Twelve 288-pin |
| Memory module capacities |
RDIMM
| 16 GB or 32 GB |
Minimum RAM
| 64 GB |
Maximum RAM
| Up to 192 GB with single processor
Up to 384 GB with dual processor |
| RAID controller |
Controller type
| PERC 9 family |
This section provides hard drive specifications for your hardware.
Hard drive specification| Type | Specification |
|---|
| Four hard-drive systems | 2x SATA SSD + 2x 3.5" NL-SAS HDD |
This section provides connectors specifications for your hardware, including rear, front, and internal connectors.
Connector specifications| Type | Specification |
|---|
| Rear |
NIC
| Four 10/100/1000 Mbps |
Serial
| 9-pin, DTE, 16550-compatible |
USB
| One 9-pin, USB 3.0-compliant
One 4-pin, USB 2.0-compliant |
Video
| 15-pin VGA |
External vFlash card
| One optional vFlash memory card NOTE: The card slot is available for use only if the iDRAC8 Enterprise license is installed on your system. |
| Front |
USB
| Two 4-pin, USB 2.0-compliant |
Video
| 15-pin VGA |
| Internal |
USB
| One 9-pin, USB 3.0-compliant |
Internal Dual SD Module (IDSDM)
| One flash memory card slot with the internal SD module |
This section provides video specifications for storage, including type, and memory.
Video specifications| Type | Specification |
|---|
| Video type | Integrated Matrox G200 |
Video memory | 16 MB shared |
This section provides environmental specifications for storage, including temperature, relative humidity, maximum vibrations, particulate contamination, gaseous contamination, and expanded operating temperature.
NOTE: For more information about environmental measurements for specific system configurations, see Dell.com/environmental_datasheets.
Environmental specifications| Type | Specification |
|---|
| Temperature |
Storage
| –40°C to 65°C (–40°F to 149°F) |
Continuous operation (for altitude less than 950 m or 3117 ft)
| 10°C to 35°C (50°F to 95°F) with no direct sunlight on the equipment. |
Maximum temperature gradient (operating and storage)
| 20°C/h (36°F/h) |
| Relative humidity |
Storage
| 5% to 95% RH with 33°C (91°F) maximum dew point. Atmosphere must be non-condensing at all times. |
Operating
| 10% to 80% Relative Humidity with 29°C (84.2°F) maximum dew point. |
| Maximum vibration |
Storage
| 0.26 Grms at 5 Hz to 350 Hz (all operation orientations). |
Operating
| 1.88 Grms at 10 Hz to 500 Hz for 15 min (all six sides tested). |
| Maximum shock |
Storage
| Six consecutively run shock pulses in the positive and negative x, y, and z axes of 40 G for up to 2.3 ms. |
Operating
| Six consecutively run shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for up to 2 ms. |
| Maximum altitude |
Operating
| 3,048 m (10,000 ft) |
Storage
| 12,000 m (39,370 ft) |
| Operating altitude de-rating |
Up to 35°C (95°F)
| Maximum temperature is reduced by 1°C/300 m (1°F/547 ft) above 950 m (3,117 ft). |
35°C to 40°C (95°F to 104°F)
| Maximum temperature is reduced by 1°C/175 m (1°F/319 ft) above 950 m (3,117 ft). |
40°C to 45°C (104°F to 113°F)
| Maximum temperature is reduced by 1°C/125 m (1°F/228 ft) above 950 m (3,117 ft). |
| Particulate contamination |
| NOTE: This section defines the limits to help avoid IT equipment damage and/or failure from particulates and gaseous contamination. If it is determined that levels of particulates or gaseous pollution are beyond the limits specified below and are the reason for the damage and/or failures to your equipment, it may be necessary for you to re-mediate the environmental conditions that are causing the damage and/or failures. Remediation of environmental conditions is the responsibility of the customer. |
Air filtration
| Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95% upper confidence limit. Note: - Applies to data center environments only. Air filtration requirements do not apply to IT equipment designed to be used outside a data center, in environments such as an office or factory floor.
- Air entering the data center must have MERV11 or MERV13 filtration.
|
Conductive dust
| Air must be free of conductive dust, zinc whiskers, or other conductive particles.
NOTE: Applies to data center and non-data center environments. |
Corrosive dust
| - Air must be free of corrosive dust.
- Residual dust present in the air must have a deliquescent point less than 60% relative humidity.
NOTE: Applies to data center and non-data center environments. |
| Gaseous contamination | |
| Note: Maximum corrosive contaminant levels measured at ≤50% relative humidity. |
| Copper coupon corrosion rate | <300 Å/month per Class G1 as defined by ANSI/ISA71.04-1985. |
| Silver coupon corrosion rate | <200 Å/month as defined by AHSRAE TC9.9. |
The documentation matrix provides information about the documents that you use to configure and deploy the Dell web-scale converged appliance solution.
WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included with this document or as a separate document.
Make sure that you read through any media that ships with your system that provides documentation and tools for configuring and managing your system, including those pertaining to the OS, system management software, system updates, and system components that you purchased with your system.
NOTE: URLs such as Dell.com/support or Dell.com/support/home, are not active, because you must type the URL from your location to access your specific language.
For the full name of an abbreviation or acronym used in this document, see the Glossary at Dell.com/support/home.
NOTE: Always check for updates on Dell.com/support/home and read through the updates first because they often supersede information in other documents.
NOTE: While upgrading your system, Dell recommends that you download and install the latest BIOS, driver, and systems management firmware on your system from Dell.com/support/home.
Dell documentation is either included with your shipment or available at the Dell website at Dell.com/xcseriesmanuals.
Dell documentation for:
- Dell iDRAC is available at Dell.com/idracmanuals.
- Dell OpenManage Essentials is available at Dell.com/openmanagemanuals.
To access Dell documetation:
- In the Dell Support page, scroll down to General Support, and then click Servers, Storage & Networking.
- Click Engineered Solutions, click Manuals , and select the documentation you require.
Dell reference documentation| To learn about... | Refer to... |
|---|
| Setup instructions of your system, including the technical specifications | Getting Started Guide |
Hardware details for your system | Owner's Manual |
| How to install your system in to a rack | Dell Rack Install Guide |
| How to deploy and set up this solution | Solutions Guide |
| Setting up and using Dell iDRAC8 | Dell iDRAC8 Quick Start Guide |
| Using OpenManage Essentials to monitor, perform updates, view hardware, and view inventory on your system | Dell OpenManage Essentials User's Guide |
Nutanix documentation has different document titles depending on the Nutanix solution software you are using. The table here shows you the document title equivalence between the two operating systems for the Nutanix documents used with the XC Series solution.
Nutanix reference documentation for Dell XC Series| To learn about... | Nutanix Operating System 4.1 | Acropolis base (NOS) 4.5 document name |
|---|
| Comprehensive instructions and references for the Nutanix UI, including overview information. | Web Console Guide | Prism Web Console Guide |
| Set up instructions for your solution. | Setup Guide | Field Installation Guide |
| Set up instructions for environments with special requirements and restrictions. | Advanced Setup Guide | Acropolis Advanced Setup Guide |
| Managing Nutanix Acropolis AHV hosts that run Nutanix solution software. | Acropolis Virtualization Administration Guide | Acropolis Hypervisor Administration Guide |
| Comprehensive references for Controller Virtual Machine (CVM) utilities, nCLI commands, and Nutanix PowerShell cmdlet. | Command Reference | Acropolis Command Reference |
| Instructions and reference for administering the Nutanix solution software outside the Nutanix Prism UI (such as cluster start/stop, manual upgrade, changing passwords, reconfiguring IP addresses, and troubleshooting tools). | NOS Advanced Administration Guide | Acropolis Advanced Administration Guide |
| Managing VMware ESXi hosts that run Nutanix solution software, including VMware vCenter requirements. | vSphere Administration Guide | vSphere Administration Guide for Acropolis |
| Managing Hyper-V hosts that run the Nutanix solution software, including domain requirements. | Hyper-V Administration Guide | Hyper-V Administration for Acropolis |
| Comprehensive references for the Nutanix REST API. | API Reference | Acropolis API Reference |
Software instructions for hardware components that are not functioning. | Hardware Replacement Documentation | Hardware Replacement Documentation |
How to locate Nutanix documentation (Back to top)
You can view Nutanix document based on the privileges you are provided. There are two types of user:
NOS 4.1 Nutanix documentation for Dell XC Series| Document name | Software type | Release | All or Platform |
|---|
| Documentation available for Guest user |
| Acropolis Virtualization Administration Guide | NOS | 4.1 | All |
| API Reference | NOS | 4.1 | All |
| Command Reference | NOS | 4.1 | All |
| Hyper-V Administration Guide | NOS | 4.1 | All |
| Setup Guide | NOS | 4.1 | All |
| vSphere Administration Guide | NOS | 4.1 | All |
| Web Console Guide | NOS | 4.1 | All |
| Documentation available for Privileged user |
| Advanced Setup Guide | NOS | 4.1 | All |
| Hardware Replacement Documentation | NOS | 4.1 | XC Series |
| Acropolis Virtualization Administration Guide | NOS | 4.1 | All |
| API Reference | NOS | 4.1 | All |
| Command Reference | NOS | 4.1 | All |
| Hyper-V Administration Guide | NOS | 4.1 | All |
| Setup Guide | NOS | 4.1 | All |
| vSphere Administration Guide | NOS | 4.1 | All |
| Web Console Guide | NOS | 4.1 | All |
NOS Advanced Administration Guide | NOS | 4.1 | All |
Acropolis base (NOS) 4.5 Nutanix documentation for Dell XC Series| Document name | Software type | Release | All or Platform |
|---|
| Documentation available for Guest user |
| Acropolis API Reference | Acropolis base (NOS) | 4.5 | All |
| Acropolis Hypervisor Administration Guide | NOS | 4.5 | All |
| Hyper-V Administration for Acropolis | Acropolis base (NOS) | 4.5 | All |
| vSphere Administration Guide for Acropolis | Acropolis base (NOS) | 4.5 | All |
| Documentation available for Privileged user |
| Acropolis Advanced Administration Guide | Acropolis base (NOS) | 4.5 | All |
| Acropolis Advanced Setup Guide | Acropolis base (NOS) | 4.5 | All |
| Acropolis Command Reference | Acropolis base (NOS) | 4.5 | All |
| Field Installation Guide | Foundation | 4.5 | All |
| Hardware Replacement Documentation | Platform | 4.5 | XC Series |
| Acropolis API Reference | AHV | 4.5 | All |
| Acropolis Hypervisor Administration Guide | Acropolis base (NOS) | 4.5 | All |
| Hyper-V Administration for Acropolis | Acropolis base (NOS) | 4.5 | All |
| vSphere Administration Guide for Acropolis | Acropolis base (NOS) | 4.5 | All |
Prism Web Console Guide | Prism | 4.5 | All |
Dell provides several online and telephone-based support and service options. If you do not have an active internet connection, you can find contact information about your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical assistance, or customer-service issues:
- Go to Dell.com/support.
- Select your country from the drop-down menu on the lower right corner of the page.
- For customized support:
- Enter your system Service Tag in the Enter your Service Tag field.
- Click Submit.
- The support page that lists the various support categories is displayed.
- For general support:
- Select your product category.
- Select your product segment.
- Select your product. The support page that lists the various support categories is displayed.
- For contact details of Dell Global Technical Support:
- Click Global Technical Support.
- The Contact Technical Support page is displayed with details to call, chat, or e-mail the Dell Global Technical Support team.
Quick Resource Locator
Use the Quick Resource Locator (QRL) to get immediate access to DHMS Solution information. This information provides access to reference documentation, a link to the Dell support page, and links to hardware-specific QRL pages, which include how-to videos. You can access this information by visiting www.dell.com/QRL or by using your smartphone or tablet and scanning the QR code below. You can also click the image below to go directly to the DHMS QRL location.
!["QRL]()
(Back to top)
Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.
2016 - 07
Rev. A05
Tags: Dell XC430 Web-Scale Hyperconverged Appliance Support Matrix
